Home > Plug And > Plug And Play Configuration Error Dell Optiplex

Plug And Play Configuration Error Dell Optiplex

For a USB printer, ensure that the Print to the following port(s): setting is USB. For a PCI card, set Primary Video Controller to Auto. See "Drive Problems" for troubleshooting suggestions. CAUTION: Before you perform this procedure, see "CAUTION: Safety Instructions." Check the power supply cable connections Turn off the computer and devices, disconnect them from their electrical outlets, wait 10 to check over here

Viruses can sometimes prevent Windows from recognizing the drive. Loading...Oops :Please try again. Tumbleweed36, Jul 24, 2004 #13 takatomon Thread Starter Joined: Mar 2, 2004 Messages: 188 well i tried an tried all of those del/f# combos and all i got was the beeps. Dell OptiPlex GXa 300MTbr EM+ Phoenix BIOS takatomon, Jul 24, 2004 #12 Tumbleweed36 Joined: Feb 13, 2004 Messages: 736 I don't know about the Dell...try f8, f2, and f1, see http://en.community.dell.com/support-forums/desktop/f/3514/t/2701745

Any suggestions would be appreciated! Click Appearance and Themes. yellowyellowgreenyellowPossible expansion card failureRemove each expansion card individually, and restart the computer to retest.Reinstall the expansion card(s) one at a time, and restart the computer to retest.Move each expansion card one

In PCI jargon region 2 is "base address 2" (or "base address register 2"), etc. Intel Pentium... i bought this PC to SOLVE problems, but i've only had one unsolvable problem after another. i was hoping that it would let me make changes eg.

Repeat this process until you identify which card is malfunctioning. Replace the battery only with the same or equivalent type recommended by the manufacturer. Bad error-correction code (ECC) on disk read— The floppy or hard drive controller detected an uncorrectable read error. http://arstechnica.com/civis/viewtopic.php?t=792162 If the printer is listed, right-click the printer icon.

Restart the computer. Check for interrupt request conflicts— See "Resolving Software and Hardware Incompatibilities." Power Problems CAUTION: Before you perform this procedure, see "CAUTION: Safety Instructions." NOTE: If the power light on the front Restart the computer. Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More...

Exit system setup and restart the computer. it won't take me to the "PnP interface". Check the keyboard cable Ensure that the keyboard cable is firmly connected to the computer. yellowgreenyellowgreenMemory is detected, but a memory configuration or compatibility error existsBe sure that the memory modules are compatible with your computer.

Run the Dell Diagnostics— Reboot the computer and run the Dell Diagnostics. check my blog Sep 17, 2008 | PC Desktops 1 Answer Compaq desktop presario w98SE If there is no power when inserting the ethernet card. Run the Dell Diagnostics. I have a Dell OptiPlex GX 110 with a message that reads, "Plug and Play Configuration Error!" every time I turn my computer on.

i just saw your instructions after i posted this reply. Clean the drive— Use a commercially available cleaning kit. too. this content Swap the power cables— Swap the computer and monitor power cables to determine if the power cable is defective.

i have no idea how to navigate the windows nightmare to get to bios setup. Track this discussion and email me when there are updates If you're asking for technical help, please be sure to include all your system info, including operating system, model number, and Slide the write-protect notch to the open position.

Add × Loading...

Reply With Quote 05-01-2004,06:45 AM #6 morpethmike View Profile View Forum Posts Junior Member Join Date Mar 2004 Location Morpeth England Posts 17 ok will try will report back thanks Mike Run the speaker diagnostics— Some speaker systems have self- diagnostics. f4 or ones that i configure for specific programs. Test the video card Turn off the computer and devices, disconnect them from their electrical outlets, wait 10 to 20 seconds, and open the computer cover.

takatomon, Aug 2, 2004 #15 Sponsor This thread has been Locked and is not open to further replies. Memory write/read failure at address, read value expecting value— A memory module may be faulty or improperly seated. Diagnostic Lights To help you troubleshoot a problem, your computer is equipped with four lights on the back panel labeled "A," "B," "C," and "D". have a peek at these guys If the new mouse works, the original mouse was faulty.

Follow the instructions on the screen. No boot sector on hard-disk drive The computer configuration information in system setup may be incorrect. Installed the software, but it won't allow me to install the driver for the card. Drive not ready— No floppy disk is in the drive.

Memory parity errors occur on parity-enabled computers. holding the del. I followed all the istructions that came with it. CovertCliffy Seniorius Lurkius Registered: Aug 21, 2002Posts: 12 Posted: Thu Aug 22, 2002 7:25 pm I may be wrong on this, but I think that on these wacky dell motherboards they

Por favor Ingresar o Registrarse ¿Perdiste tu email de activación?. | Foro | Web | Blog | Wiki | Ayuda | Buscar | Ingresar | Registrarse | 24 Octubre 2016, 09:13 Try another PCI slot. Turn the computer off— If your computer locks up and you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold Sector not found— The operating system cannot locate a sector on the floppy or hard drive.Run the Windows error-checking utility to check the file structure on the floppy disk or hard