Plug And Play Configuration Error Dell Gx260
Sign up! Run the Dell Diagnostics. Sector not found The operating system cannot locate a sector on the floppy or hard drive.Run the Windows error-checking utility to check the file structure on the floppy disk or hard Check for interrupt request conflicts See "Resolving Software and Hardware Incompatibilities." System Board Problems Fill out the Diagnostics Checklist as you complete the following checks. check over here
Check for viruses Use a virus-scanning program to check the hard drive, floppy disks, or CDs. Ensure that you properly installed and configured the program See the documentation that came with the software for information. I can't find the reason why, please help!! Ensure that the power supply cables are securely connected to the system board (see "System Board Components"). http://en.community.dell.com/support-forums/desktop/f/3514/t/17897168
See "Drive Problems" for troubleshooting suggestions. For a USB printer, ensure that the Print to the following port(s): setting is USB. Memory tests terminated by keystroke A keystroke interrupted the memory test. Recently upgrade hard drive to 400 GB.
Posted on Nov 29, 2008 Helpful 0 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Anonymous Re: Plug & Play Configuration If a large number of sectors are defective, back up the data (if possible), and then reformat the floppy disk or hard drive. Check for interrupt request conflicts See "Resolving Software and Hardware Incompatibilities." Memory Problems CAUTION: Before you perform this procedure, see "CAUTION: Safety Instructions." If you receive an insufficient memory message Save If the problem persists, contact Dell.
Windows NT® Press
If any of the diagnostics tests fail, the card you just reinstalled is faulty and needs to be replaced. Run the Dell Diagnostics Reboot the computer and run the Dell Diagnostics. If the error appears again, contact Dell. The email address entered is already associated to an account.Login to post Please use English characters only.
If no replacement drive is immediately available and the drive is not the only bootable drive, enter system setup and change the appropriate drive setting to None. https://foro.elhacker.net/dudas_generales/problema_dell_plug_and_play_configuration_error-t202542.0.html;msg962059 Insert a floppy disk into the drive and try again. Check for interrupt request conflicts See "Resolving Software and Hardware Incompatibilities." Back to Contents Page Connect with us facebook twitter CNET Reviews Top Categories CNET 100 Appliances Audio Check the speaker cable connections Ensure that the speakers are connected as shown on the setup diagram supplied with the speakers.
Here's some information that may be helpful: System: Windows XP Professional Version 2002 Service Pack 2. Test the electrical outlet Ensure that the electrical outlet is working by testing it with another device, such as a lamp. Hit F2 for BIOS and check under boot option, or advanced, or an area to configure your video settings (AGP/PCI) etc Flag Permalink This was helpful (0) Back to PC Hardware this content The error seems to stem from the Nvidia graphics card and the Dell BIOS, which is included with the computer.
Test the device cable Swap the device's cable with a cable that works properly. Installed the software, but it won't allow me to install the driver for the card. Click Display, and then click the Settings tab.
Memory data line failure at address, read value expecting value A memory module may be faulty or improperly seated.
There was no RT2500 in the system while we tested.If the Nvidia AGP graphics card is substituted for a Matrox or ATI AGP graphics card, then there are no longer any If any of the tests fail, contact Dell. greenyellowgreenyellowPossible video card failure or bad on-board videoIf you have a video card, reseat it and restart the computer to retest. Check for interrupt request conflicts See "Resolving Software and Hardware Incompatibilities." Power Problems CAUTION: Before you perform this procedure, see "CAUTION: Safety Instructions." NOTE: If the power light on the front
Check the device cable connections Check the connector for bent or broken pins. (It is normal for most device cable connectors to have missing pins.) Ensure that the device cable is Once reported, our moderators will be notified and the post will be reviewed. Swap the power cables Swap the computer and monitor power cables to determine if the power cable is defective. have a peek at these guys yellowgreengreengreenOther failureCheck the computer message that appears on your monitor screen.
Attachment failed to respond The floppy or hard drive controller cannot send data to the associated drive. Replace the memory module(s) (see "Memory" for module installation procedures). Invalid configuration information - please run SETUP program The computer configuration information does not match the hardware configuration. Swap the computer and monitor power cables to determine if the power cable is defective.
Also if the system has boots to desktop, and I plug in the network cable it automatically goes off. For more information, see your operating system documentation. Ensure that the Serial Port setting (for a serial device) or the Parallel Port setting (for a parallel device) matches the recommended settings. Any suggestions?
All rights reserved. It guess that by removing and replacing the battery it delete the CMOS of the BIOS and force the BIOS to reinitiate and allocate all addresses from scratch. x:\ is not accessible. Keyboard failure A cable or connector may be loose, or the keyboard or keyboard/mouse controller may be faulty.
Run the Dell Diagnostics Reboot the computer and run the Dell Diagnostics. These lights can be yellow or green. You can only upload files of type 3GP, 3GPP, MP4, MOV, AVI, MPG, MPEG, or RM. See "Drive Problems" for troubleshooting suggestions.