Home > Ping Error > Ping Error Message General Failure

Ping Error Message General Failure

Contents

IP address must be specified. ... Success rate is 0 percent (0/5) Router4# In this example, the ping is not working due to "encapsulation failed". We appreciate your feedback. Top Of Page Verify Default Gateway Next, look at the default gateway. navigate here

Some applications block http traffic, peerblock for example. While Tracert does not record the address of the last hop or the path that the packet followed on the return path, it might show that the packet made it to All rights reserved. Jan 20 17:19:45.843: IP ARP: sent req src 100.0.0.4 0000.0c5d.7a0d, dst 100.0.0.5 0000.0000.0000 Ethernet0. read this article

Ping Error Message General Failure

Most often, it means that a route back to the sending host has failed. Jan 20 17:19:49.843: IP ARP: sent req src 100.0.0.4 0000.0c5d.7a0d, dst 100.0.0.5 0000.0000.0000 Ethernet0. Join them; it only takes a minute: Sign up exit status of the ping command up vote 10 down vote favorite while doing with the perl script I am stucked with more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed

Windows 2000 TCP/IP TCP/IP Troubleshooting Unable to Reach an IP Address Unable to Reach an IP Address Test Network Connection with Ping and PathPing Test Network Connection with Ping and PathPing The fix was to disable IPv6 in the network adapter properties for my Internet connection. That often fixed it within one or two reconnects. Ping Response Codes Do I need to do this?

Resolved Issue Concerned: I issued the above commands on same workstation a few weeks ago without issue. Ping Messages Explained The TTL value of a ping packet cannot be changed. This means that the ICMP packets that are entering the Serial 0 interface on Router4 are denied, and Router 4 sends an ICMP "administratively prohibited unreachable" message to the source of Use the appropriate utility or facility to check the IP routing table of the router assigned the IP address of < IP address >.

Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the Ping Output What is the main spoken language in Kiev: Ukrainian or Russian? In practice, most Linux systems use a unique identifier for every ping process, and sequence number is an increasing number within that process. Top Of Page Show: Inherited Protected Print Export (0) Print Export (0) Share IN THIS ARTICLE Is this page helpful?

Ping Messages Explained

Router2# ! ! http://superuser.com/questions/433416/why-do-i-get-general-failure-when-pinging-host-name-on-a-win-7-node-on-the-net Yes No Tell us more Flash Newsletter | Contact Us | Privacy Statement | Terms of Use | Trademarks | © 2016 Microsoft © 2016 Microsoft

Success rate is 0 percent (0/5) The above output shows that Router4 is broadcasting packets by sending them to the Ethernet broadcast address FFFF.FFFF.FFFF. check over here Here, the 0000.0000.0000 means that Router4 is looking for the MAC address of the destination 100.0.0.5. We are sending our packets, but we are not receiving anything. This is because, on Router2, the packets are now handled at interrupt level. For A Web Page, Html Represents The:

Why does a full moon seem uniformly bright from earth, shouldn't it be dimmer at the "border"? Jan 20 17:04:07.167: IP: s=100.0.0.4 (local), d=100.0.0.5 (Ethernet0), len 100, sending Jan 20 17:04:07.171: IP: s=100.0.0.4 (local), d=100.0.0.5 (Ethernet0), len 100, encapsulation failed. If the remote routing tables are correct and contain a valid route back to the sending host, to see if the ARP cache lacks the proper address, use the arp -a his comment is here We recommend that you carefully read Use the Debug Command before issuing debug commands.

Router2 is quite busy, and answering the ping is not its main priority. Ping Protocol http://www.manpagez.com/man/8/ping The actual return values may depend on your system. Your cache administrator is webmaster.

You can refer to this IANA link for more information regarding types and codes for ICMP.

In some cases, this is not enough to travel the required number of links to a destination. A better way to test router performance is with traffic going through the router: The traffic is then fast-switched, and is handled by the router with the highest priority. Increase the wait time using the ping -w switch. Different Ping Errors Three datagrams are sent, each with a Time-To-Live (TTL) field value set to one.

The Echo Request typically does not receive any reply if the host was sleeping in hibernation state, but the host still wakes up from sleep state if its interface is configured When a packet destination is the router itself, this packet has to be process-switched. Unknown packet type. & Packet lifetime exceeded. http://newmexicosupercomputer.com/ping-error/ping-error-5.html Router1#ping 12.0.0.2 Type escape sequence to abort.

U.S. Echo request[edit] The echo request ("ping") is an ICMP message. 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 Routing Issue Interface Down Access-list Command Address Resolution Protocol (ARP) Issue Delay Correct Source Address High Input Queue Drops The Traceroute Command Performance Use the Debug Command Related Information Introduction This interface Serial1 ip address 12.0.0.2 255.255.255.0 ! !

The return values are listed near the bottom. It uses a series of Internet Control Message Protocol (ICMP) Echo messages to determine: Whether a remote host is active or inactive. Microsoft Customer Support Microsoft Community Forums United States (English) Sign in Home Library Wiki Learn Gallery Downloads Support Forums Blogs We’re sorry. For all the options about this command, see Trace (privileged).

Unfortunately 6to4 is very unreliable in practice and for many people it is completely broken. ICMP Header (in red): Type of ICMP message (8 bits) Code (8 bits) Checksum (16 bits), calculated with the ICMP part of the packet (the IP header is not used). The system returned: (22) Invalid argument The remote host or network may be down. Router4(config)# access-list 100 permit tcp any any eq telnet Router4(config)#interface s0 Router4(config-if)#ip access-group 100 in Router1#configure terminal Enter configuration commands, one per line.